Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
225,000	US Dollar	each

Tire Industry Equipment - Columbus McKinnon Shredder- T-02409. Columbus McKinnon is a leader in the tire shredding/recycling industry. Their knife and rotor set up are designed to produce a very clean chip. This package of Columbus McKinnon equipment is a rare find in the used equipment marketplace. The package includes a full CM 2 speed system, including a screen for producing a 2 inch nominal tire chip and the conveyors needed to make this a turn key system. In addition, the package includes another CM 2 speed with a broken shaft, to repair or use for parts.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
255,000	US Dollar	each

Tire Industry Equipment - Eldan 122T Rasper System- T-02413. The Eldan line of equipment has been a top manufacturer of tire recycling equipment for over 55 years. The Eldan 122T Rasper is a heavy duty machine ideally suited for the harsh application of scrap rubber processing. This machine will take a 2 inch chip down to a 1 inch chip at a rate of about 2 ton of material per hour The system is currently all mounted on a single drop, triple axle axle trailer. We will make sure that all the lights and brakes and tires are all working properly on the trailer to make it travel ready. The system will include a factory built in-feed conveyor, the refurbished Eldan 122T Rasper, a factory built out-feed conveyor, a self-cleaning cross-belt magnet going across the out-feed conveyor, and a factory built long out-feed dis-charge conveyor. In addition, the system has an aspiration system that is not located on the trailer. This system will come complete with a centrally located electrical control panel and be ready to be hooked up to your power source. This system will require a 400 kw generator set to run it, or hook it up to electric power. This is a top notch system, ready to go to work.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
145,000	US Dollar	each

Tire Industry Equipment - SSI 2000E Shredder- T-02415. This SSI shredder is a great, moderately sized tire shredder, capable of handling car and light pick up truck tires. Currently the knives are double stacked, allowing the machine to easily handle semi truck tires, also. This 2000E is very similar to the very popular SSI 2400, except the shafts on the 2000E are a bit shorter, creating a very robust shredder, and tremendously minimizing the instance of a shaft failure. The owner is installing new knives, and will check over the bearings and replace the endplate seals at that time. The rails and fingers are in great condition, and the control panel is in excellent condition. This shredder is powered by a 200 hp electric motor, and the electric control panel is in excellent condition. The shredder has a very nice catwalk all the way around the machine making it easy to access the shredder. In addition to new knives installed, the owner will steam clean and paint the shredder and catwalk. It will look and run like a new machines. It comes with infeed and outfeed hoppers. This shredder includes a spare full set of knives that need to be rebuilt.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
37,500	US Dollar	each

Tire Industry Equipment - Portable Eagle Truck Tire Derimmer- T-02418. The Eagle Truck Tire Derimmer can handle removing the rim out of truck tires, and bigger tires as well. This portable unit is powered by a 20 hp Kohler gas engine. The cycle time is about 20 second. It’s got a 2 inch standard ball hitch for easy moving of the unit. The owner is currently using it periodically, so it’s in good running condition. The derimmer was designed to allow the tire to be rolled into the unit, not lifted, minimizing any back issues and worker’s compensation claims.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
27,500	US Dollar	each

Tire Industry Equipment - Portable Eagle Super Slicer- T-02417. The multipurpose Eagle Super Slicer allows you to remove the sidewalls and the steel beads from car and truck tires. This portable unit is powered by a 20 hp Kohler gas engine. The cycle time is about 12 seconds on a truck tire measuing up to 44” outside diameter, and 8 seconds on a car tire. This gives you a production rate of about 50-70 tires per hour. It’s got a 2 inch standard ball hitch for easy moving of the unit.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
27,500	US Dollar	each

Tire Industry Equipment - Portable Eagle Tuf Cut- T-02416. The Eagle Tuf Cut adds flexibility to your tire processing operation by allowing you to accept and process tires up to 23.5/25 12 ply into your system. This portable unit is powered by a 20 hp Kohler gas engine. It comes standard with a hydraulic tire lift and rollers to be able to manage the bigger tires. You can cut about 60 truck tires or 120 to 150 passenger tires an hour. The owner will install a new battery and turn it on to make sure it runs.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
195,000	US Dollar	each

Tire Industry Equipment - Barclay 4.9 Tire Shredder- T-02414. Barclay is a well respected name in the tire recycling industry. The 75 hp motor makes it inexpensive to run, while still producing the power for the tough application of tire shredding. This is a 2000 model and it is currently in operation, so it’s running good. The custom 6 ft wide infeed conveyor comes with the shredder, as well as the motor and control panel. It is ready to go to work.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
225,000	US Dollar	each

Tire Industry Equipment - Columbus McKinnon Tire Shredder, T02409. Columbus McKinnon is a leader in the tire shredding/recycling industry. Their knife and rotor set up are designed to produce a very clean chip. This package of Columbus McKinnon equipment is a rare find in the used equipment marketplace. The package includes a full CM 2 speed system, including a screen for producing a 2 inch nominal tire chip and the conveyors needed to make this a turn key system. In addition, the package includes another CM 2 speed with a broken shaft, to repair or use for parts.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
115,000	US Dollar	each

Tire Industry Equipment - Satrind Tech Shredder- T-01236. This Satrind Shredder is a very clean machine. With a 100 hp electric motor and 3 inch 4-hook knives, it can be a great shredder for a variety of products like drums, msw, plastics, car tires and electronic waste. It was running when it was taken out of service, it comes with an infeed hopper and shredder stand, as well as an electrical control panel.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
95,000	US Dollor	each

Tire Industry Equipment - Barclay 6P Tire Shredder- T-02386. Barclay is a leader in the tire industry in rough shredding and preshredding tires. Designed to take whole tires as large as 72 inches in diameter, Barclay 6P Primary Tire Shredders cleanly shear high volumes of scrap tires into strips in just second. The 50 hp electric motor makes it very inexpensive to operate. This Barclay doesn’t come with any conveyors, but it is in excellent condition. This Barclay comes with a brand new control panel that has not been installed yet. It also has a feed roll for more efficient tire feeding.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
495,000	US Dollar	each

Tire Industry Equipment - Granutech/ Saturn Model 80 Grizzly System- T-01243. The Granutech/Saturn Model 80 Grizzly is the premier machine for taking 2 inch chips down to a 1 inch minus TDF. The heavy rotor and 400 hp gives this machine the power it needs to process 2 inch chips to a 1 inch minus granule at a rate of about 3 ton per hour This system has everything you need to put this after a 2 inch chip system, including an infeed conveyor, the Grizzly, a vibratory discharge conveyor, outfeed conveyor, crossbelt magnet and an aspiration system. We are installing new bed and fly knives on the machine, and new wear liners and new screens. The control panel will be completely rebuilt with a 500 Amp disconnect, a soft start and all the controls. This is a very high production machine and it is the best machine on the market today used to remove up to 80-85% of the steel from your tires while reducing the 2” x 2” size tire chips down to 1 inch or less in size. These machines are the work horse of today’s tire processing industry and are built much more robust than most of their competition. You won’t find a nicer used machine on the market today!

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
335,000	US Dollar	each

Tire Industry Equipment - SSI M100E Shredder system- T-02355. SSI is a highly respected name in the shredder industry. This 2007 M100 is powered by a 200 hp electric motor and the shredder is in excellent running condition. The shredder is a primary system, including an infeed and outfeed conveyor, and electric controls. This shredder has just been rebuilt, including new knives and spacers, bearings, and seals. The outfeed conveyor has been rebuilt as well, with a new belt installed. This machine is in like new condition and ready to go to work. In addition, there is a spare set of shafts and a spare set of knives that need to be rebuilt that goes with this system.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
165,000	US Dollar	each

Tire Industry Equipment - Columbus McKinnon Tire Chipper- T02382. Columbus McKinnon is a leader in the scrap tire processing industry, and this CM Chipper is no exception. This dual drive chipper was in line behind a CM Primary shredder, producing about 14 ton per hour of 2 inch chips when the knives were new. When the knives had some wear the production dropped to about 8 ton per hour. This shredder comes with the infeed hopper, electric control panel with PLC touch screen, including soft start, and the motor.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
call for pricing	US Dollar	each

Tire Industry Equipment - MacSaturn 72x46 Shredder- T-01230. MacSaturn has been a leader in the tire shredding industry for years. This 72x46 is a good sized shredder, able to handle a variety of materials from tires, some purgings, light metals, oversize material like furniture. It is hydraulically powered by a 300 hp hydraulic power unit. We are taking this machine into our shop to look it over and replace or rebuild components as needed. We have the endplate back from the machine shop and the machine is back together. We will paint the shredder the color of your choice, the conveyors are safety yellow. The machine has double stacked 2 inch knives for a 4 inch one pass cut. We are setting this shredder up as a primary, one pass shredder system. The system comes with a brand new infeed and brand new outfeed conveyor, as well as a shredder stand, hydraulic power pack, and control panel.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
195,000	US Dollar	each

Tire Industry Equipment - MacSaturn 72x50 Shredder system- T-02364. MacSaturn is a leader in the waste reduction industry. This is one of their larger shredders, the opening is 72 inches by 50 inches, and is powered by 2 Detroit 671 Diesel Engings. The large hopper opening allows for a 5 ft tire to be run through the shredder. The knives are currently stacked with a 4 inch cut, and there is a spare set of knives that will go with the system.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
227,500	US Dollar	each

Tire Industry Equipment - Columbus McKinnon Tire Chipper Shredder- T0183B. This CM Chipper is a great machine for taking preshredded tires and taking them down to a manageable material. We have completely refurbished this machine, including installing new hardened rotors. The rotors are made out of a heat treated 4140 material, rather than the mild steel they are usually built with. We have done this so that when a knife comes off while the machine is in operation and you don’t catch it immediately you shouldn’t harm your knife seats near as easily. In addition these will have the multi-stack cutters meaning that they will have 1.9, 1.8, as well as 1.7 knife seats available to put knives on. Because there are so many 2.0 machines in the field, there is a plentiful supply of used 2 inch blades that can be bought for a fraction of the cost of a new blade. They can be ground down to be used on the 1.9 seat, then on the 1.8, and finally on the 1.7 seat. This way you can use a knife 3 times, greatly reducing your maintenance costs. This machine will be powered by a 250 H.P. electric motor and have a soft start in order to reduce the amperage draw on startup. This chipper would work ideally in conjunction with any other primary shredder that you currently have installed. This shredder will have in-feed hopper, stand, and out-feed hopper. An infeed and outfeed conveyor is available for an additional charge.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
59,500	US Dollar	each

Tire Industry Equipment - Portable Eagle Tire Baler and Double Hopper- T-01202. Eagle International has a reputation for making top quality equipment for the tire recycling industry. The Eagle Tire Baler was designed to: eliminate collection of waste water, reduce fire hazard, and to provide beneficial usage of waste tires in baled form. These baled tires have been used as fences and even walls for buildings or houses. Baling tires also allows you to retrieve a product, if mono-filled for future uses. This machine will bale approximately 100 passenger size tires into a 30” x 54” x 60” cube, held together with 5 wire ties. This baler is capable of baling four bales per hour or thirty two bales in an 8 hour shift therefore it will equate to processing 3200 scrap waste tires per day. This baler looks to be in very good condition and has been previously owned by a city. So it has been maintained very well and besides having the paint a little faded from sitting out in the hot Southwest dessert sun the machine looks to be in excellent shape. The machine we have for sale is a gooseneck style hitch and the tires all look to be in very good condition. This unit is completely portable and is powered by an Isuzu diesel engine. The machine will be checked over by our shop and be ready to work once it reached your location. In addition to this Eagle Tire Baler we are also selling and Eagle Tire Double Hopper to go along with this unit to help with getting your tires hauled to the baler without having to keep moving the baler around all the time. This Eagle Tire hopper is powered off two of the hydraulic control valves that are mounted on the Eagle Baler. So this is just a value added benefit that goes along with the purchase of this Tire Baler. This is an excellent opportunity for you to purchase a very nice lightly used package of equipment at a very reasonable price.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
179,000	US Dollar	each

Tire Industry Equipment - Morbark 1300A Tub Grinder- CA permitted- W-021237. This 13-foot portable tub grinder is powered by a rebuilt 1,000 HP CAT Diesel engine. Unit has a grapple loader & tilt tub. This will work great for processing stumps, trees, pallets, C&D, green waste, and much more at a rate up to about 320 yards per hour depending on the material being processed. The grinder is in great operating condition, call today for more details! California permitted & ready to go right to work!

Quantity	Units	Frequency
1	pair	once
Price	Funds	Per Unit
call	US Dollar	pair

Tire Industry Equipment - Columbus McKinnon Tire Shredder System including a 2 speed Shredder and Chipper- T-01190. This used Columbus McKinnon Tire shredding system was owned by a state agency so this equipment was subject to a very good preventative maintenance program and should be ready to be put to work at your location. See below the complete list of equipment that makes up this tire shredding package. Equipment List: 1. Whole Tire in-feed conveyor 36” wide X 30’ long- this is a factory built Columbus McKinnon conveyor. 2. Columbus McKinnon Primary (2) speed shredder with 250 H.P. electric motor with 2.2 knives installed. 3. Short Shredder out-feed conveyor 24” wide X 10’ long- this is a factory built Columbus McKinnon conveyor 4. Long Shredder out-feed conveyor 24” wide X 30’ long- this is a factory built Columbus McKinnon conveyor 5. Columbus McKinnon Chipper shredder with 200 H.P. electric motor with 1.8 knives installed 6. Short Chipper out-feed conveyor 30” wide X 10’ long- this is a factory built Columbus McKinnon conveyor 7. Long Chipper out-feed conveyor 30” wide X 30’ long- this is a factory built Columbus McKinnon conveyor 8. Columbus McKinnon Super classifier (2) deck disc screen classifier (note daisy wheels are worn pretty bad and will need some attention in the not too distant future). 9. Return Conveyor 30” wide X 30’ long- this is a factory built Columbus McKinnon conveyor 10. Sized Material out-feed conveyor 30” wide X 30’ long- this is a factory built Columbus McKinnon conveyor 11. Cross-belt self-cleaning magnet and magnet stand All the knife seats look good on both the primary shredder and the chipper. This should make someone a very good whole tire down to 2” TDF processing system. We have many pictures as well as a video of all the equipment as it was set-up where we purchased it.

Quantity	Units	Frequency
1	each	once
Price	Funds	Per Unit
675,000	US Dollar	each

Tire Industry Equipment - Raptor Shear Shredder or Shredder System- T-01181. We currently have for sale (1) used (IDM) Raptor Model R-163 Shredder powered directly by (2) 200 H.P. or (2) 250 H.P electric motors through a Reggiana gear reducer. The shredder will have an opening of 57” x 66” and will have brand new knives installed. This unit will work great for shredding semi-truck tires at a very high production rate. This is without a doubt one of the highest production machines manufactured in the United States today. And in combination with this high production factor they are also the most user friendly machines to operate and work on in the industry. I have attached an information sheet on some benefits of the Raptor Shredder. This Shredder will be set up with a custom built in-feed hopper, a custom built shredder stand and complete electric control panel. We can add a brand new custom built heavy duty disc screen classifier, and custom build whatever conveyors that you might need to complete the whole tires to chip system, price is $525,000 for the chip system. (Information sheet below) Reasons for buying the Raptor brand shredders compared to other brands! 1. Raptor offers the industries only lift out rotor (shaft) assemblies “Lift and Swap” design. No other current shredder manufacture offers this time savings feature. Typically make this change in 2-4 hours (depending on your individual situation) and have your machine back up and running. If you don’t have a spare set of rotors then you just change out the knives by removing the end plate and changing the knives in a traditional manner. The “Lift and Swap” design allows you to leave your cleaning fingers in place when you make a knife change. 2. Raptor offers either electric or hydraulic driven shredders with several different versions of each model. These come in single or dual drive. The electric and hydraulic driven shredders come factory equipped with fully automated and programmable touch screen controls. The hydraulic dual drive shredders have what we call “independent shafts”. Each shaft maybe controlled independent of the other. This allows for more flexibility in the programming for the tough to shred materials. 3. Raptor has shaft sizes that are much larger in diameter than the industry standards, and we custom build each shredder to meet your particular application. 4. Raptor offers both stationary and mobile shredders to meet any shredding application that you might have. Raptor offer production out-put capacities from 3 tons to 35 tons per hour depending on the materials being processed. 5. Raptor has three different styles of shredders: primary shredder (shreds whole off-road, semi-truck, or passenger tires), chipper (takes any pre-shredded tire material down to 2” chips), and tire grinder (takes 2” tire chips down to ¾” and liberates the majority of the wire out of the rubber). Each of these use the basic same cutter box, shaft assemblies, bearings, and drive components which allows the customer to easily change from one application to another with our “Lift and Swap” rotor design. . 6. Raptor shredder has several different types of knife or rotor cutter designs to meet your particular shredding needs. The solid rotor may come with industry standard solid hook style knife, or the IDM proprietary bolt-on knife design, or as well as the traditional CM style bolt-on knife design with the side wear plates. The major difference is our knife seats are manufactured out of heat treated 4140 steel, with each bolt hole inserted with a heat treated insert. This makes for easy knife seat repairs, by simply unscrewing the insert and replacing with a new one. 7. The Raptor shredder also offers a much improved stack locking system for keeping your knives tight on your cutter shafts. This is the true secret to keeping a set of knives cutting good for a longer period. These shredders come with both splash plates & seal guards to protect the seals. The bearings are housed in field replaceable housings with seals on both sides using grease instead of oil. 8. Raptor shredder can be equipped with an optional integrated screen for the sizing of materials before it leaves your shredder cutting chamber. (note this will limit the output production of the shredder) 9. Raptor shredder has many different cutting chamber sizes that run from a width of 47.5 inches up to 55 inches and a length of 44 inches up to 72 inches. These shredders are offered in a range from 150 H.P. – 500 H. P. to meet or exceed your shredding needs. We also offer the shredder with many different in-feed hopper configurations including a self-extracting hopper for quick and easy cutting chamber ac